Installation of Guigang PPH winding tank
Comparison of PPH mixing tank price and PP mixing tank and maintenance measures. It is necessary to use electric heating to melt and extrude the particles onto the steel mold, which consumes a lot of power. The PP storage tank only has the power of the welding gun, so it consumes less power; The raw material of PPH mixing tank is PPH granular material, and the raw material of PP storage tank is polypropylene plate. The price of PPH granular material is more expensive than polypropylene plate; Cooling and demoulding are required, which are performed by electric device, but not for PP storage tank; Steel molds are required for processing, and natural gas is required for preheating before processing. The startup cost is high, and PP storage tank is directly rolled into a tank with polypropylene plates, so the cost is low; The PPH mixing tank is welded with a large extrusion electric heating drag gun, which consumes a lot of power. The PP storage tank uses a small manual drag gun, which consumes less power.
Installation of Guigang PPH winding tank
For the treatment of corrosive gases (such as acid and alkaline waste gas) in PPH waste gas tower, liquid absorption method is often used. The key to control the waste gas by liquid absorption is the selection of purification equipment. The main development is acid and alkaline waste gas purification process and equipment with high purification efficiency, simple operation and management, and long service life. This process and product are characterized by simple structure, low energy consumption, high purification efficiency and wide application range, and can effectively remove water-soluble gases such as hydrogen chloride (HCl), hydrogen fluoride (HF), ammonia (NH3), sulfuric acid mist (H2SO4), chromic acid mist (CrO3), cyanuric acid gas (HCN), alkali vapor (NaOH), hydrogen sulfide gas (H2S), formalin (HCHO), etc. The acid mist waste gas is introduced into the purification tower through the air duct. After passing through the packing layer, the waste gas and sodium hydride absorption liquid are fully contacted, absorbed and neutralized by gas-liquid two-phase reaction. After purification, the acid mist waste gas is dewatered and defogged by the demister, and then discharged into the atmosphere by the fan. The absorption liquid is sprayed down from the tower top after being pressurized by the water pump at the tower bottom, and then flows back to the tower bottom for recycling.
Installation of Guigang PPH winding tank
PPH tank body extrusion winding production tank body butt welding is the process of using PPH spiral extrusion winding unit to process PPH particles into tank body molding. The system adopts the process of hot melting PPH particles, extruding them, and then winding them onto steel dies to form cans. The production efficiency is 5-8 times higher than that of manual production. The product has good integrity, no seams, good corrosion resistance, good leakage resistance, flat and beautiful product, thin tank body and thick tank body, low price, unlimited product size and shape, and the product is processed with granular materials, with good anti-aging performance. Polypropylene tank itself has the advantage of internal and external anti-corrosion, so it can be stored in some highly corrosive environments. Because linear polyethylene is used, it has good service performance, and the special structure of polypropylene rolling tank is used, so the service life can basically reach more than 15 years. In addition, it can be used under normal atmospheric temperature and pressure when it is stored.
Installation of Guigang PPH winding tank
HDPE is a part of the plastic recycling market with rapid growth. This is mainly because it is easy to reprocess, has a limited degradation characteristics and is widely used in packaging. The main recycling is to reprocess 25% of recycled materials, such as post consumer recyclables (PCR), with pure HDPE to make bottles not in contact with food. In addition, due to the good insulation performance of HDPE storage tanks, polyethylene is used in many cables, and has good impact resistance even in low environment, In addition, this type of storage tank is more convenient for processing, and can be processed again after use, but it can not be used in industries directly contacting food after secondary processing.
